琪琪色原网站在线观看,国产伦精品一区二区三区免费,久久99精品久久久久婷婷,国产freesexvideos中国麻豆

Analysis of Jiangmen Motorcycle parts forging technology and die design of Automobile Forging

2019-12-29 1040

  With the development of automobile industry and China's accession to WTO, the quality and cost price of automobile forgings in domestic and international market are becoming more and more demanding, such as draft angle, weight tolerance, size, machining allowance and other requirements are very high, and the price is not ideal, but the batch is very large. In order to meet the market demand, this paper analyzes and practices the technology repeatedly, and finds an ideal technology, which is of great significance to the production of similar products.

  Product introduction and determination of process plan

  Product introduction

  The arm is a part used for the brake pump of heavy duty vehicle, and its structure is shown in Fig. 1. There are several difficulties in forging: (1) the draft angle is small, only 3 ° outside and 5 ° inside, while the ejector has only one place in ∮ 62 hole; (2) the machining allowance is small, and only boring and broaching are used for machining ∮ 62 and 23.2mm square groove; (3) the 10 nails of 10 - ∮ 6.2 * 5 are full of difficulties and have high position requirements, and the root fillet of the nail is r0.2, which makes the mold wear faster and the production flow faster In the process, it is easy to bump and cause deformation.

  Determination of process plan

  In order to adapt to mass production and improve efficiency, we have determined the following processes: (medium frequency furnace) heating / (cross wedge rolling) blank making / (25000kN hot die forging press) bending / pre forging / final forging / (3150kN double point press) punching / trimming / normalizing / shot blasting / precision pressing. In the technological process, two pieces are used at a time for heating, the part handle is long and thin, and the efficiency of free forging single piece is low. Use wedge cross rolling blank (as shown in Figure 2), and cut into two pieces on the rolling mill at the same time. Because the cross-section of the part changes greatly, from ∮ 55 to ∮ 23, it needs two wedges to complete, so it is difficult to process and repair the rolling die.

  In addition to ensuring the size of pressing head and handle, it is more important to correct the position of 10 nails, the fillet of root and the bending of handle. Therefore, two standard pressing plates with five holes are used to ensure the position of the nail and the round corner of the root, thus improving the service life of the forging die.

  Key points of mold design and manufacture

  Generally, in the design of the press bending die, only the shape bending of the extruded blank is considered to be consistent with that of the forging. Because the thickness difference between the big end of the arm and the handle is large, when the pre forging die is put in, the handle of the bent blank will be suspended. During the pre forging, the transition between the handle and the big end will be folded. Because the handle of the bent blank is suspended, the metal flow in this part is too large during the pre forging. Therefore, the design of the bending blank must make the bending blank on the pre forging die to make its shape consistent with the pre forging die.

  Jiangmen Motorcycle accessories http://dealbeamer.com//


国产人与禽zoz0性伦| 欧美又粗又大xxxxbbbb疯狂| 99精品视频在线观看免费| 欧美性猛交xxxx黑人| 久久久久久人妻无码| 三级做a全过程在线观看| 亚洲av午夜精品无码专区| 精品国模一区二区三区| 国产精品免费久久久久影院仙踪林| 熟妇高潮精品一区二区三区| 亚洲日韩国产精品乱-久| 又湿又紧又大又爽a视频国产| 国语对白做受xxxxx在线中国| 亚洲欧洲日本综合aⅴ在线| 欧洲熟妇色 欧美| 久久天天躁狠狠躁夜夜96流白浆| 性饥渴的农村熟妇| 黄又色又污又爽又高潮动态图| 亚洲春色在线视频| 亚洲av无码专区亚洲av伊甸园| www国产亚洲精品久久网站| 精品无码国产一区二区三区51安| 亚洲精品宾馆在线精品酒店| 亚洲 小说 欧美 激情 另类| 野外性史欧美k8播放| 人妻少妇精品视频一区二区三区 | 免费人成视频在线| 特黄 做受又硬又粗又大视频| 色欲av伊人久久大香线蕉影院| 国产成人无码av| 亚洲无线码一区二区三区| 亚洲v欧美v国产v在线观看| 精品人妻系列无码一区二区三区| 精品无码久久久久国产| 国产综合色在线视频区| 一区二区三区在线 | 欧| 处破痛哭a√18成年片免费 | 十八禁视频网站在线观看| 无码午夜成人1000部免费视频| 日韩精品无码av中文无码版| 国产成人小视频|